Shipping across Canada & the USA — samples free, you cover shipping
U-Chain Request a quote

02 — Aluminum & LED baseboard

Baseboard, reduced to a line.

Extruded aluminum instead of painted MDF. Four profile families from 19 mm to 102 mm, twelve factory finishes, corner pieces instead of mitres — and one profile with an LED channel cut into the top edge.

Black aluminum baseboard installed along a white marble wall above a grey marble floor, showing the thin profile and the clean line where it meets the floor

The material

A painted MDF baseboard is a consumable. It swells at the cut ends in a bathroom, it crushes where the vacuum hits it, and every joint is a caulk line waiting to crack. Three years in, it is the part of the room that looks tired first.

Ours is extruded aluminum with a factory finish. It does not absorb water, it does not burn, it does not need priming or painting, and the corners are moulded pieces rather than mitred joints. The face is 1/8″ thick, so it reads as a drawn line at the base of the wall instead of a band of trim.


Aluminum against the alternatives —

  Aluminum (ours) MDF Timber PVC
Swells in damp No — aluminum Yes, at the cut ends Moves seasonally No
Burns No — non-combustible metal Yes Yes Yes, and drips
Dents from a vacuum Resists Chips and crushes Dents Scuffs
Needs painting No — factory finish Yes, primer + 2 coats Yes No
Needs caulk + filler No — corner pieces Yes, every joint Yes Yes
Takes an LED strip Yes — A-9 channel No No No

Four profiles —

They are not four styles of the same thing. Each one solves a different problem, and the one you want is usually decided by how far along the build is.

  • Dark grey aluminum baseboard turning an outside corner with a moulded corner piece, shown on white beside black and white profiles of the same section

    A-2

    Minimalist

    Flat face, square top

    The default. A flat 1/8″ face that sits tight to the wall and turns out to a 1/2″ foot at the floor. Four heights, the widest finish range in the catalogue, and a full set of corner and end-cap accessories so nothing has to be mitred.

    Heights
    1⅝″ · 2⅜″ · 3⅛″ · 4″
    Metric
    41 · 60 · 79 · 102 mm
    Finish
    12 finishes
  • Recessed aluminum baseboard installed under a wood-panelled wall, the panel sitting on the profile so the face finishes flush, with four sizes in gold and black lined up in front

    A-4

    Recessed

    Flush with the plaster line

    Sets into the wall rather than onto it, so the finished face is flush with the plaster and reads as a shadow gap. This is the one architects ask for by name and the hardest to source in North America. The 3/4″ and 1″ models have no accessories — they are cut and butted.

    Heights
    ¾″ · 1″ · 1¼″ · 2″ · 3⅛″
    Metric
    19 · 25 · 32 · 51 · 79 mm
    Finish
    Black, iron grey, gold
  • Graphite aluminum baseboard profile laid out beside its wall bracket, outside corner cap and end piece, showing the parts that make up the clip-on system

    A-5

    Clip-on

    Curved face on an aluminum base rail

    A two-part system: a perforated aluminum base rail fixes to the wall, and the finished face clips onto it. The face can come off later without damaging the wall, which is why it gets specified in rental and commercial fit-outs. Supplied with a single or integral base.

    Heights
    1¾″ · 2⅜″ · 3⅛″
    Metric
    45 · 60 · 79 mm
    Finish
    Single or integral base
  • Three aluminum LED baseboard profiles in black, dark grey and white standing against a marble wall, with the open LED channel visible along the top edge of each

    A-9

    LED

    Surface-mounted, concealed strip

    The same curved face with an open channel along the top edge that takes a 1/4″ LED strip. The light washes up the wall and the strip itself is never in view. Two heights, four finishes, end caps and corners — no connector, so runs are cut to length.

    Heights
    2″ · 3⅛″
    Metric
    51 · 79 mm
    Finish
    Black, dark grey, white, matte gold

Full geometry —

Every model code and dimension we hold, taken from the current catalogue. Nothing here is rounded to make a table look tidy.

A-2 — Minimalist

Model Height Metric Face Foot
A-2-A4 1⅝″ 41 mm ⅛″ ½″
A-2-A6 2⅜″ 60 mm ⅛″ ½″
A-2-A8 3⅛″ 79 mm ⅛″ ½″
A-2-A10 4″ 102 mm ⅛″ ½″

Length 2.5 m. Accessories — inside corner, outside corner, connector, left and right end caps — in 1⅝″, 2⅜″ and 3⅛″.

A-4 — Recessed

Model Height Metric Length Finishes
A-4-A8 3⅛″ 79 mm 2.5 m Black, iron grey
A-4-A5 2″ 51 mm 2.5 m Black, gold, iron grey
A-4-A3 1¼″ 32 mm 2.5 m Black, gold, iron grey
A-4-A2.5 1″ 25 mm 3.0 m Gold
A-4-A2B ¾″ 19 mm 2.5 m Black, iron grey
A-4-A2A ¾″ 19 mm 3.0 m Gold

Corner and end-cap accessories on the 1¼″ and 2″ models only. The ¾″ and 1″ profiles are cut and butted. No connectors in this family.

A-9 — LED

Model Height Metric Channel Strip width
A-9-A5 2″ 51 mm ½″ × ⅝″ ¼″ / 6 mm
A-9-A8 3⅛″ 79 mm ½″ × ⅝″ ¼″ / 6 mm

Length 2.5 m. Black, dark grey, white and matte gold. End caps, inside and outside corners; no connector.

A note on units: the catalogue is printed in inches, but the lengths convert to exactly 2.5 m and 3.0 m — these are metric extrusions quoted in imperial, which is why the fractions read oddly. If you are specifying in millimetres, ask and we will send the manufacturer's metric figures rather than have you work from a conversion.


Four aluminum LED baseboard profiles with their concealed strips lit — black, matte gold, dark grey and white — throwing warm light across a concrete floor

A-9

Light at the floor line.

A 1/2″ × 5/8″ channel runs the length of the top edge and takes a standard 1/4″ LED strip. The strip sits below the lip, so you see the wash on the wall and never the diodes.

It replaces the two things people usually do instead — surface channel screwed above the baseboard, or a plastered shadow gap that has to be designed in at framing. This is a baseboard that arrives with the detail already in it.

  • Close view of a black aluminum LED baseboard with the concealed strip lit, warm light washing up the wall above the profile

    Black, lit. The channel lip reads as a hairline above the wash.

  • Close view of a white aluminum LED baseboard with the concealed strip lit, warm light washing up the wall above the profile

    White, lit. Same profile — it disappears into a pale wall entirely.


Hand pressing a black aluminum baseboard onto a wall, with beads of construction adhesive visible along the back of the profile

On site

No nail holes. No caulk line.

The flat profiles bond straight to the wall — the back face is serrated to key into construction adhesive, and the run is done as fast as you can cut it. Nothing to fill, nothing to sand, nothing to touch up.

The clip-on family works the other way: a perforated aluminum base rail goes on first and the finished face snaps onto it, so it can be taken off later without opening the wall. Corners and ends are moulded pieces, so a square cut is all the accuracy the job needs.


Twelve finishes —

Factory-applied, so there is no painting on site and no colour drift between one length and the next. Not every finish is made in every height — the stocked combinations are below.

Aluminum baseboard shown in six finishes fanned out on white — gold, silver, grey, light grey, dark grey and black — with a gold outside corner wrapping the wall corner at left
  • Black 1⅝ · 2⅜ · 3⅛ · 4″
  • White 1⅝ · 2⅜ · 3⅛ · 4″
  • Grey 1⅝ · 2⅜ · 3⅛ · 4″
  • Dark grey 1⅝ · 2⅜ · 3⅛ · 4″
  • Gold 1⅝ · 2⅜ · 3⅛ · 4″
  • Rose gold 1⅝ · 2⅜ · 3⅛ · 4″
  • Silver 1⅝ · 2⅜ · 3⅛″
  • Iron grey 1⅝ · 2⅜ · 3⅛″
  • Light grey 1⅝ · 2⅜ · 3⅛″
  • Milk grey 1⅝ · 2⅜ · 3⅛″
  • Champagne 1⅝ · 2⅜ · 3⅛″
  • Warm white 1⅝ · 2⅜ · 3⅛″

Other colours available for customisation. Send a reference and we will tell you what is possible and at what quantity.


Questions we get asked —

What sizes does aluminum baseboard come in?
Across the four families, heights run from 3/4″ (19 mm) to 4″ (102 mm). The minimalist A-2 range covers 1 5/8″, 2 3/8″, 3 1/8″ and 4″; the recessed A-4 range starts at 3/4″ and goes to 3 1/8″; the LED A-9 range is 2″ and 3 1/8″. Standard lengths are 2.5 m, with two A-4 models supplied at 3.0 m.
How is it fixed to the wall?
Two ways, depending on the profile. The A-5 clip-on family uses a perforated aluminum base rail that fixes to the wall first, with the finished face clipping onto it — so the face can be removed later without damage. The flat A-2 profiles are usually bonded straight to the wall with construction adhesive; the back of the profile is serrated to key into it. Neither method needs nail holes filled or a caulk line afterwards.
Do I still have to mitre the corners?
No. Every family except the two smallest recessed profiles ships with moulded inside corners, outside corners and left/right end caps. The straight runs are cut square and the corner piece covers the junction. That is the main reason these get specified over MDF on a fast fit-out — a square cut and a corner cap is a far more repeatable result than a 45-degree joint on a wall that is not square.
Can I use it in a bathroom or a basement?
Yes. Aluminum does not absorb water, so there is nothing to swell, delaminate or grow mould the way MDF does at its cut ends. It is also non-combustible as a material, which is why it turns up in commercial corridors and multi-unit residential. If your project needs a specific tested fire rating for a submittal, ask us for the current documentation rather than relying on this page.
What is a recessed baseboard, and do I need a special wall?
A recessed or flush baseboard sets into the wall build-up instead of sitting proud of it, so the finished face lines up with the plaster and reads as a shadow gap rather than as trim. It has to be planned before the drywall goes on — the profile is fixed to the studs and the board is brought down to it. Retrofitting one into a finished wall is not practical, so if you want the A-4 range, decide at framing stage.
Does the LED profile come with the strip and driver?
The A-9 profile takes a 1/4″ (6 mm) LED strip in the channel along its top edge. Tell us the total run length and whether you want the strip, and we will quote it either way — many contractors already have a preferred strip and driver and only need the extruded channel.
Can I order baseboard online?
No — and unlike the corner appliques, there is no version of this that works in a cart. These are 2.5-metre extrusions. Freight on overlength aluminum changes enormously with destination and carrier, and a guessed shipping figure would either overcharge you or lose us money on every order. Send your run lengths and the delivery address to info@uchain.ca, or use the contact form, and you will get a real freight number.
Are the finishes shown the only ones available?
No. Twelve finishes are stocked across the A-2 range and the catalogue notes that other colours are available for customisation, as are other profile dimensions. If you are matching hardware or a window frame, send us the colour reference and we will tell you whether it can be produced and what the minimum quantity would be.

Send us the run lengths.

Tell us the rooms, the total metres and the delivery address, and we will come back with profiles, finishes and an honest freight number. These are 2.5-metre extrusions — there is no cart that can price that properly, so we do it by hand. Samples are free; you cover shipping only.